HOW TO MAKE A CANOPY WITH YOUR OWN HANDS FROM POLYCARBONATE, WOODEN, COTTAGE, PHOTO

The canopy is a kind of roof structure that is designed to protect against all kinds of precipitation.

Initially, such structures were built in the villages. A little later, awnings began to be constructed as shelter from the rain on street shelves and markets.

Generation after generation, century after century, has led to the fact that the range of canopies has become unusually wide. The same applies to the materials from which they are made.

Despite the large selection of roofing materials for sheds, polycarbonate sheds are becoming increasingly popular.

The fact is that this polymer material has the ease of its installation, has a low specific and relatively high cost.

Plus, it is transparent, but has a protective layer against UV penetration.

Due to such properties of polycarbonate, it is not difficult for even an experienced common man to make a typical canopy.

We build a quality barn with our own hands.
Learn how to make a bird feeder //rusfermer.net/postrojki/sadovye-postrojki/dekorativnye-sooruzheniya/kormushki-dlya-ptits-svoimi-rukami-iz-podruchnyh-materialov.html.
Read the article here about the healing properties of mint.

We build a canopy of polycarbonate

To build a polycarbonate canopy with your own hands, it is necessary to determine roofing dimensions. This is necessary in order to accurately measure and calculate all the dimensions of the future frame with all its structural elements.

It is necessary to take into account the fact that the frame of the canopy under the polycarbonate roof must be made of a metal profile (channel, angles, pipe rolling, etc.).

Such a design of the frame will make it tough and unshakable from the winds, as well as other mechanical and physical effects, which adversely affect the integrity of the polycarbonate sheets (it is very fragile). So, a small project or sketch already exists.

Polycarbonate canopy on concrete

Consider the simplest design of a polycarbonate canopy on concrete. For this we need 2 channels of 2 m height, and 2 channels of 2.5 m height. We weld pyataks with pre-drilled holes for the anchor to the ends of 4 channels.

Then we mark up the places on the concrete, where we will install our racks from channels. Punch the drill in the concrete holes for mounting racks by means of anchors.

Next, set the channel with the coppers along the holes drilled in the concrete and fasten it with anchors (we preliminarily define a clear angle of 90 degrees).

It should be noted that we expose a channel with identical lengths on one side. So, stands under the perimeter canopy we are ready.

Next, we connect the upper ends of our racks with corners by welding. If this is not enough for the rigidity of the structure, then additionally throw stretch marks or struts. When everything is ready, then proceed to the installation of crates for polycarbonate.

According to the standards of polycarbonate fasteners, the size of the cell of the batten should not exceed 1 m / sq. Weld the crate either from a corner of 50 mm, or from a square tube of the same size. Such a width of the mounting plane under the joints of polycarbonate sheets will allow a well to fasten the connecting sheet profile.

By and large, it is much easier to buy one large sheet of polycarbonate and fix it on the crate. But if there is no such possibility, then we buy an installation connecting sheet profile and polycarbonate of the corresponding sizes. Plus, we need thermo washers. They will help to avoid a strong load on the places of screwing the polycarbonate to the profile plane.

Learn from our article how to dry dogrose.
Learn all the useful things about garden blackberries //rusfermer.net/sad/yagodnyj-sad/posadka-yagod/ezhevika-razmnozhenie-posadka-uhod-poleznye-svojstva.html. Grow on health!

When everything is ready, we start covering the pre-made frame with the crate. It is very important that the polycarbonate is located honeycomb along the slope of the canopy. Such a design will avoid the accumulation of moisture in the comb.

The above information describes the essence of building a canopy of polycarbonate and is one of the possible options for the construction of the roof. The shapes and sizes of the roof of a polycarbonate roof may be different, but the very essence of the typical cover remains the same. If for many people polycarbonate is an expensive material, then wood can be used with ease for shedding.

Wooden canopies

Wooden canopies, unlike metal canopies, are not very durable, but much cheaper. If you already have a desire to build a wooden shed, then you will need the materials exactly the same as for the metal shed, but only wooden (boards, cant, slats, etc.).

The erection technology remains exactly the same, but we use nails, screws and corners as welding, and choose slate as the roofing material, since it is relatively light, quickly fastened with slate nails and durable.

Note gardener: Raspberry, planting and care.
We make garden paths of wood //rusfermer.net/postrojki/sadovye-postrojki/dekorativnye-sooruzheniya/sadovye-dorozhki-elementy-dizajna-svoimi-rukami.html.